{"product_id":"overclocker-flex-for-nintendo-game-boy-advance-sp-gba-sp-handheld-robot-retro","title":"Overclocker Flex for Nintendo Game Boy Advance GBA SP AGS handheld accelerator | Robot retro","description":"\u003cb\u003eFeatures:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003e- Overclock flex mod for Game Boy Advance SP\u003cbr\u003e- Provides easier install using flex pcb\u003cbr\u003e- up to 170% clock speed increase\u003cbr\u003e- Compatible with IPS screen mods\u003cbr\u003e- Medium difficulty level, soldering \u0026amp; crystal removal required.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eDescription:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003eThe robot_retro GBA SP overclocker flex mod provides a simple way of overclocking or underclocking your Gameboy advance SP.\u003cbr\u003e\u003cbr\u003eThe installation process has been tidied and simplied with the use of a flex PCB, only 3 wires are needed to be soldered to test points.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eNOTE: Whilst the mod can be soldered by hand, the crstal will need to be removed, ideally with hot air.\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003e\u003cb\u003eHighlights:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003e- Supports adjustable clock speeds at 30%, 50%, 75%, 130%, 150%, and 170% of the base clock.\r\n\u003cbr\u003e- Increase speed: Press Select and R shoulder button together\r\n\u003cbr\u003e- Decrease speed: Press Select and L shoulder button together\r\n\u003cbr\u003e\u003cbr\u003eOptional LED indicator\u003cbr\u003e:\r\n\u003cbr\u003e- Power LED blinks faster when overclocked\r\n\u003cbr\u003e- Power LED blinks slower when underclocked\r\n\u003cbr\u003e- Solid green LED at base (stock) speed\r\n\u003cbr\u003e\u003cbr\u003eTop speed limits configurable to 170%, 150%, or 130% depending on your screen setup:\r\n\u003cbr\u003e\u003cbr\u003eDefault max speed: 170% (Hispeedido v5)\r\nBridge solder jumper S1 to limit max speed to 150% (for stock LCD)\r\n\u003cbr\u003e\u003cbr\u003eBridge solder jumper S2 to limit max speed to 130% (for Funnyplaying IPS 3.0 inch and HISPEEDIDO \"One Chip\" v2)\u003cbr\u003e\u003cbr\u003e\u003cb\u003eOther Features:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003e- Very low power consumption.  Measured as \u0026lt;15mA using the Nordic Power Profiler Kit II.\u003cbr\u003e- Accurate base clock (4.194Mhz).  Measured as \u0026gt;0.01% accurate.  \u003cbr\u003e- There is will no difference between this mod and the original GBA crystal at stock speeds.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eInstallation:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003eMulticoloured wire is included to aid with the install.\r\n\u003cbr\u003e\u003cbr\u003eRemove the original GBA SP crystal.  (Recommended: Use a hot air station for clean removal)\r\n\u003cbr\u003e\u003cbr\u003eInstall the flex mod as per the photos.\r\nSolder the 3 points highlighted in pink circles.\r\nRun wires to the 3 test points shown as the red, pink and blue wires. \r\nUse flux for best soldering results.\r\n\u003cbr\u003e\u003cbr\u003e(Optional) To enable the LED speed indicator, solder the green wire as shown.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eSpeed Limiting:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003e- Bridge solder jumper S1 to cap speed at 150%\r\n\u003cbr\u003e- Bridge solder jumper S2 to cap speed at 130%\u003cbr\u003e\u003cbr\u003eDeveloped in collaboration with RJS FPGA\u003cbr\u003e\u003cbr\u003e\u003cdiv id=\"zl-diy\"\u003e\n\u003cstrong\u003eDIY part.\u003c\/strong\u003e This is a DIY part for you to fit yourself. Fitting needs care and, where stated, soldering or other technical skills – see our \u003ca href=\"https:\/\/zedlabz.com\/blogs\/guides\"\u003efitting guides\u003c\/a\u003e. We're not responsible for damage caused by incorrect fitting, or for an existing fault in your console. Replacing a part may not fix your fault, as faults can have more than one cause. This doesn't affect your statutory rights.\u003cbr\u003e\u003cbr\u003e\n\u003c\/div\u003e\u003cdiv id=\"zl-safety\" class=\"zl-safety\" data-zl-ver=\"1.0\" data-zl-sym=\"SP,KOR,HOT,VENT,GUIDE\" data-zl-file=\"ZL-IF-ROBOTRETRO\"\u003e\n\u003cb\u003eSafety information:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003e- Not a toy. Keep out of reach of children.\u003cbr\u003e- Small parts – choking hazard.\u003cbr\u003e- Soldering required – ventilate, beware hot iron.\u003cbr\u003e- Switch off, unplug and remove any batteries before fitting.\u003cbr\u003e- Fits listed models only – do not force.\u003cbr\u003e- Fitting guides: zedlabz.com\/blogs\/guides\u003cbr\u003e- Follow the manufacturer's instructions.\u003cbr\u003e\u003cbr\u003e\n\u003c\/div\u003e\u003cdiv id=\"zl-mfr\"\u003eBrand \/ manufacturer: Robot Retro · Importer \/ seller: Assecure Ltd (ZedLabz), The Outbuildings, Grove Farm Road, Maldon, Essex, CM9 8LR, UK · support@zedlabz.com\u003cbr\u003e\u003cbr\u003e\n\u003c\/div\u003e\u003cdiv id=\"zl-eurp\"\u003eEU responsible person (for authorities only): FFB Estonia OÜ · Päevalille tn 6-15, Haabersti linnaosa, 13517 Tallinn, Harju maakond, Estonia · finance_estonia@fulfillment-box.com\u003c\/div\u003e","brand":"Robot Retro","offers":[{"title":"Default Title","offer_id":48661960917244,"sku":"300251","price":275.0,"currency_code":"NOK","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1810\/1427\/files\/tqshyb0jo15.png?v=1768037927","url":"https:\/\/www.zedlabz.com\/en-no\/products\/overclocker-flex-for-nintendo-game-boy-advance-sp-gba-sp-handheld-robot-retro","provider":"ZedLabz","version":"1.0","type":"link"}