{"product_id":"usb-c-power-supply-replacement-for-sega-saturn-console-psu-power-board-robot-retro","title":"USB C Power supply replacement for Sega Saturn console PSU power board | Robot retro","description":"\u003cb\u003eFeatures:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003e- Provides convenient and efficient power to your Saturn console.\u003cbr\u003e- Replaces the stock power supply in most models of Saturn (see compatibility)\u003cbr\u003e- Requires a USB C wall plug and USB C cable (not included)\u003cbr\u003e- Easy install, no soldering needed, screw driver needed (not included)\u003cbr\u003e\u003cdiv\u003e- Includes black USB C spacer (other colours available seperately)\u003cbr\u003e\u003cbr\u003e\n\u003c\/div\u003e\u003cb\u003eDescription:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003eThe OEM Saturn power supply is a combined 110v\/240v AC to DC converter. This is quite inefficient and noisy, which can manifest in a “fuzzy” video signal. \u003cbr\u003e\u003cbr\u003eAlso, plugging in a UK 240v supply to a 110v Japanese Saturn can cause damage to the Dreamcast.\u003cbr\u003e\u003cbr\u003e\u003cb\u003eCompatibility: This upgrade is compatible with all Saturn models with the exception of VA0 (Type A power supplies). \u003cbr\u003e\u003c\/b\u003e\u003cbr\u003e\u003cb\u003eWorks with Fenrir ODE optical drive replacement mod.\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003eYou will need your own USB C wall adapter and USB C cable, a 5v or 20v Power Delivery USBC charger such as those from Anker, uGreen and other reputable brands, most 30W charger USBC will work (they have to be able to output 15v\/20v)\u003cbr\u003e\u003cbr\u003eA screwdriver is the only thing needed to install this power board, no soldering or other technical skills needed. (Screwdriver not included)\u003cbr\u003e\u003cbr\u003e\u003cb\u003eWhat the robot_retro Saturn Power Board Offers:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003ePowered from a 15v or 20v Power Delivery USBC charger (e.g. Ankur, Dell, uGreen, etc.). Most 30W charger USBC will work (they have to be able to output 15v\/20v).\u003cbr\u003eWorks with all PAL and US\/Japan NTSC models except VA0 (Type A power supplies). Also removes the risk of accidentally plugging in 240V into a 110V system and causing damage.\u003cbr\u003eWorks perfectly with Fenrir.\u003cbr\u003eIncludes 5V header for Noctua fans and dedicated 12V\/9V\/5V\/3.3V\/GND 2.54mm pin headers for other power-hungry mods\u003cbr\u003eTested to be between 90 and 95% efficient across all loads. \u003cbr\u003eLow signal noise and heat.\u003cbr\u003eDrop in solution. No soldering, wires or complicated install required.\u003cbr\u003eNo flashing LEDS, perfect for clear shells.\u003cbr\u003eOvervoltage, over temperature and fused supply.\u003cbr\u003e3D printed spacer.\u003cbr\u003e\u003cbr\u003eOther 3D spacer colours can purchase seperately\u003cbr\u003e\u003cbr\u003e\u003cb\u003eVoltage Setting:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003eThe following voltage should be set using SW1 (instructions are also on the back of the PCB):\u003cbr\u003e\u003cbr\u003eType A (VA0) = Not compatible so N\/A\u003cbr\u003e\u003cbr\u003eType B (VA1 to VA5) = +9V\u003cbr\u003e\u003cbr\u003eType C NTSC (VA6+) = +9v or +12v (either will work)\u003cbr\u003e\u003cbr\u003eType C PAL (VA6+) = Check original or use 9v if unsure\u003cbr\u003e\u003cbr\u003e\u003cb\u003eInstallation:\u003c\/b\u003e\u003cbr\u003e\u003cbr\u003eA Phillips #2 screwdriver recommended for installation.\u003cbr\u003e\u003cbr\u003eUnscrew the two power supply and five bottom shell screws as shown in the photo.\u003cbr\u003eRemove the top lid and then remove the single power board screw (see photos).\u003cbr\u003eFit the robot_retro board in exactly the same way as the OEM power board was removed. Reattach the single original screw.\u003cbr\u003eFit 3D printer USBC spacer and attach the two power supply screws. Note, this does require a gentle push to get the screws to tap into the 3D spacer. I recommend to fit the first screw around halfway, then start the second while pushing down on the 3D spacer (towards the PCB). Once both are tapped, drive them both home. Do not overtighten.\u003cbr\u003eButton up the console.\n\n\u003cp\u003e\u003cstrong\u003eBrowse the range\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"\/en-us\/collections\/retro-robot\"\u003eRobot Retro products\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"\/en-us\/collections\/retro\"\u003eRetro gaming parts and accessories\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Robot Retro","offers":[{"title":"Default Title","offer_id":46628247273724,"sku":"000534","price":55.5,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1810\/1427\/files\/usb-c-power-supply-replacement-for-sega-saturn-console-psu-power-board-robot-retro000534retro-robot-461958.jpg?v=1742212685","url":"https:\/\/www.zedlabz.com\/en-us\/products\/usb-c-power-supply-replacement-for-sega-saturn-console-psu-power-board-robot-retro","provider":"ZedLabz","version":"1.0","type":"link"}